A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
How do you feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is readily available, the task can move speedily; if you have to open a wall to remove the old tub as well as place the new bath tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually qualified yourself for the job and also are comfortable trying it. Instead of working with a service provider to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This article will certainly aid you install a brand-new bath tub in your washroom if you have already purchased a new tub and don't need to alter the arrangement of your previous water supply pipelines.
Your tools and material checklist need to comprise the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water. After doing so, switch on the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making sure that the washing machines are in place in between the tap and the sink. Protect the tap in place with the manufacturer supplied backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply as well as check all joints as well as new pipework for leakages as well as tighten them if required. Fill the bath tub and additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the tub must wait until the bath tub has actually been utilized at least when as this will certainly settle it right into its final placement.
Preparing for the Installation
Firstly, the supporting frame provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with moisture as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also installations. They are offered in tubes and cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to enable the movement experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our topic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for spending some time to read through our article post. Make sure you take a moment to distribute this post if you liked it. I love reading our article about Tools You Need to Install a New Bathtub .
No more stress, ring now. Report this page